Charger Victron Skylla-i 24-100 (1+1) - SKI024100000

1.321,56 VAT inc.

TAXES INC.

Input voltage (VAC): 230 V
Input voltage range (VAC): 185-265 V
Input voltage range (VDC): 180-350 V
Frequency (Hz): 45-65 Hz
Power factor: 0,98
Weight: 7 kg
Dimensions: 405 x 250 x 150 mm.

Producto disponible para la venta
Finance your purchase with Cetelem
Reference: SKI024100000 Categories: ,

Product information

Victron Skylla-i 24-100 Charger (1+1): two outputs for charging 2 banks of batteries

The Victron Skylla-i 24-100 Charger (1+1) has 2 isolated outputs. The second output, limited to approximately 4 A, and with a slightly lower output voltage, is designed to fully charge a starter battery.

Skylla-i (3): three full-current outputs for charging 3 battery banks

The Skylla-i (3) has 3 isolated outputs. All outputs can supply the full rated output current.

Robust

Aluminium epoxy powder coated housings, with drip shield and stainless steel hardware, withstand the rigours of the harshest environments: heat, humidity and salt air. The printed circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that electrical components will always operate within specified limits, automatically reducing the output current if necessary under environmental conditions.
extremes.

Flexible

In addition to the CAN-bus interface (NMEA 2000), a rotary switch, DIP switches and potentiometers are available to adapt the charging algorithm to a particular battery and its conditions of use.

Important features:

Synchronised parallel operation

Several chargers can be synchronised with the CAN-bus interface. To do so, simply connect the chargers with RJ45 UTP cables. Operation: Two-output and three-output chargers cannot be connected in parallel. Please refer to the manual for more information.

The right amount of charge for a lead-acid battery: variable absorption time

When the discharge is shallow, the absorption phase is shortened to avoid overcharging the battery. After a deep discharge, the absorption charging time is automatically increased to ensure that the battery is fully recharged.

Preventing damage caused by over-gassing: BatterySafe mode

If a combination of high charging current and high absorption voltage has been chosen to charge a battery quickly, Skylla-i will prevent damage from over-gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached.

Reduced ageing and need for maintenance when the battery is not in use: storage mode

The storage mode is activated when the battery has not been discharged for 24 hours. In storage mode, the float voltage is reduced to 2.2 V/cell (26.4 V for 24 V batteries) to reduce gassing and corrosion of the positive plates. Once a week, the voltage is brought back up to the absorption level to "refresh" the
battery. This function prevents electrolyte stratification and sulphation, the main causes of battery failure.

For a longer battery life: temperature compensation

All Skylla-i chargers come with a battery temperature sensor. When connected, the charging voltage will automatically decrease as the battery temperature increases. This function is especially recommended for sealed lead-acid batteries and/or when large temperature fluctuations are expected in the battery.

Battery voltage sensor

To compensate for voltage losses due to cable resistance, the Skylla-i has a voltage probe function so that the battery always receives the correct charging voltage.

Suitable for AC and DC power supply (AC-DC and DC-DC operation)

The chargers also support DC power.

Use as a power supply

Thanks to its perfectly stabilised voltage output, the Skylla-i can be used as a power supply in cases where batteries or compensating capacitors are not available.

Li-Ion (LiFePo4) ready

Simple on/off control can be implemented by connecting a relay or optocoupler with open collector output from a Li-Ion BMS to the remote control port of the charger. Full voltage and current control is also possible by connecting to the galvanically isolated CAN-bus port.

Learn more about batteries and charging

To learn more about batteries and battery charging, please refer to his book "Energy Unlimited" (available free of charge from Victron Energy and downloadable at www.victronenergy.com).

Datasheet Victron Skylla-i 24-100 (1+1) Charger - SKI024100000

See Victron Skylla-i 24-80 (1+1) Charger data sheet - SKI024100000

Additional information

Weight8 kg
Dimensions15 × 25 × 40,5 cm

Product reviews

Reviews

There are no reviews yet.

Be the first to review “Cargador Victron Skylla-i 24-100 (1+1) – SKI024100000”

Delivery deadlines

At FVComponents.com we have stock of the references with the highest turnover, however our catalogue is so wide and economical because we work with many of the references on request. This means that the usual delivery time of 2-4 working days can be extended to 1-2 weeks + subsequent shipment by us. Thanks to this, we can offer very competitive and attractive prices to our customers that are difficult to match. If you wish, you can write to us via the chat on the website, call us at 968 97 83 01 or write to us at [email protected] to check if we have stock or the delivery time of the component you wish to purchase before finalising your order.