My account

"BMS NG Victron VE.Bus for NG lithium batteries - BMS300200300" has been added to your basket. View basket

Inverter Charger Victron Multiplus 48/3000VA 35A-16A - PMP483020001

736,36€

TAXES INC.

Continuous power output: 3000VA
Inverter Peak Power: 6000W
Inverter Operating Voltage: 48V
Inverter Efficiency: Pure Sine Wave
Weight of the Investor: 18kg
Inverter Dimensions: 362 x 258 x 218mm

Product available for sale

Finance your purchase with Cetelem

Reference: PMP483020001 Categories: Inverter Chargers 48V to 220V, Solar inverters

Details of the Inverter Charger Victron Multiplus 48/3000VA 35A-16A - PMP483020001

Parallel operation

Up to six Victron Multiplus 48/3000VA 35-16A Inverters can be operated in parallel to achieve a higher power output. In addition to parallel connection, three units can be configured for three-phase output by assigning each inverter to one of the three phases.

[one_half][/one_half] [one_half_last] [one_half_last] [one_half_half_last].[/one_half_last]

Uninterruptible alternating current (UPS function)

In the event of a power outage, or disconnection of the shore power or generator, the inverter integrated in the Victron Multiplus 48/3000VA 35-16A Inverter automatically activates and takes over the supply to power the connected loads. This happens so quickly (less than 20 milliseconds) that computers and other electronic equipment continue to operate without interruption.

Remote monitoring and control

When connected with a GX device (e.g. a Victron Cerbo GX MK2 Monitoring - BPP900451100) you can monitor and control the Victron Multiplus Inverter and your system(s) locally (LAN) or remotely over the Internet from anywhere in the world using the free VRM app and the free portal VRM. Access can be carried out from a phone, tablet or PC with different operating systems.

The level of control is limitless, from the setting of the Victron Multiplus 48/3000VA 35-16A Inverter to the automatic start of a standby generator. And much more...

Proven reliability

The full-bridge plus toroidal transformer topology has proven its reliability over many years. The inverter is short-circuit proof and protected against overheating, whether due to overload or high ambient temperature.

PowerControl - Limited power from generator, shore power or mains power

In the Multi Control Panel a maximum current from the generator or shore power can be set. The Victron Multiplus 48/3000VA 35-16A Inverter will take over other AC loads and use the surplus current for charging, thus avoiding overloading the generator or the shore power.

PowerAssist - Increasing the electrical capacity of the shore power outlet or generator

When a power peak is required for a short period of time, as is often the case, the Victron Multiplus 48/3000VA 35-16A Inverter will immediately compensate the possible lack of power from the grid current or generator with power from the battery. When the load is reduced, the excess power is used to recharge the battery.

Variable four-stage charger and charging of dual battery banks

The main output provides a powerful charge to the battery system via advanced "variable charge" software. The software fine-tunes the automatic three-stage process to match battery conditions and adds a fourth stage for extended periods of float.

In addition, the MultiPlus can charge a second battery using a separate limited charge output designed to charge a starter battery from the main engine or generator.

High starting power

Necessary for starting loads with high inrush current, such as converters for LED lamps, halogen lamps or power tools.

Search mode

When the search mode is activated, the consumption of the inverter in no-load operation decreases by approximately 70%. In this mode the Victron Inverter 48/1600VA 20-16A when operating in inverter mode, switches off if there is no load or too little load, and switches back on every two seconds for a short period of time.

If the output current exceeds a preset level, the inverter shall continue to operate. Otherwise, the inverter will shut down again.

Programmable relay

The programmable relay is by default configured as alarm relay, i.e. the relay will be de-energised in case of alarm or pre-alarm (inverter is too hot, input ripple is almost too high and battery voltage is too low).