You must be logged in to post a review.
- Free shipping to mainland Spain for orders over 300€.
1.321,56€ VAT inc.
Input voltage (VAC): 230 V
Input voltage range (VAC): 185-265 V
Input voltage range (VDC): 180-350 V
Frequency (Hz): 45-65 Hz
Power factor: 0,98
Weight: 7 kg
Dimensions: 405 x 250 x 150 mm.
The Victron Skylla-i 24-100 (1+1) charger has 2 isolated outputs. The second output, limited to approximately 4 A, and with a slightly lower output voltage, is intended to fully charge a starter battery.
Skylla-i (3) has 3 isolated outputs. All outputs can supply the full rated output current.
Aluminum epoxy powder-coated housings, with drip shield and stainless steel hardware, withstand the rigors of the harshest environments: heat, humidity and salt air. The printed circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that electrical components will always operate within specified limits, automatically reducing, if necessary, the output current under environmental conditions.
extreme.
In addition to the CAN-bus interface (NMEA 2000) a rotary switch, DIP switches and potentiometers are available to adapt the charging algorithm to a particular battery and its conditions of use.
Several chargers can be synchronized with the CAN-bus interface. To do this, simply connect the chargers with RJ45 UTP cables. Operation: Two-output and three-output chargers cannot be connected in parallel. Please refer to the manual for more information.
When the discharge is low, the absorption phase is shortened to avoid overcharging the battery. After a deep discharge, the absorption charging time is automatically increased to ensure that the battery is fully recharged.
If a combination of high charging current and high absorption voltage has been chosen to charge a battery quickly, Skylla-i will prevent damage from over-gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached.
The storage mode is activated when the battery has not been discharged for 24 hours. In storage mode, the float voltage is reduced to 2.2 V/cell (26.4 V for 24 V batteries) to reduce gassing and corrosion of the positive plates. Once a week, the voltage is brought back up to the absorption level to "refresh" the
battery. This function prevents electrolyte stratification and sulfation, the main causes of battery failure.
All Skylla-i chargers come with a battery temperature sensor. When connected, the charging voltage will automatically decrease as the battery temperature increases. This function is especially recommended for sealed lead-acid batteries and/or when large temperature fluctuations are expected in the battery.
To compensate for voltage losses due to cable resistance, the Skylla-i has a voltage probe function so that the battery always receives the correct charging voltage.
The chargers also support DC power.
Thanks to its perfectly stabilized voltage output, the Skylla-i can be used as a power supply in cases where batteries or compensating capacitors are not available.
Simple on/off control can be implemented by connecting a relay or optocoupler with open collector output from a Li-Ion BMS to the remote control port of the charger. Full voltage and current control is also possible by connecting to the galvanically isolated CAN-bus port.
To learn more about batteries and battery charging, please refer to their book "Energy Unlimited" (available free of charge from Victron Energy and downloadable at www.victronenergy.com).
See Victron Skylla-i 24-80 (1+1) Charger data sheet - SKI024100000
Weight | 7 kg |
---|---|
Dimensions | 15 × 25 × 40,5 cm |
You must be logged in to post a review.
At FVComponentes.com we have stock of the references with the highest rotation, however our catalog is so wide and economical because with many of the references we work under order. This means that the delivery time can be extended for 1-2 weeks + subsequent shipment by us. Thanks to this we can offer super competitive and attractive prices to the customer difficult to match. If you wish, you can write us to the chat on the page, call us at 968 97 83 01 or write to us at comercial@fvcomponentes.com to check if we have stock or the delivery time of the component you wish to purchase before finalizing the order.
Reviews
There are no reviews yet.