You must be logged in to post a review.
- Free shipping to mainland Spain for orders over 300€.
453,27€ VAT inc.
Input voltage: 230 VAC (range: 210 - 250 V)
DC input voltage: 290 - 355 VDC
Frequency: 45-65 Hz
Power factor: 0,7
House battery charging current: 30/50A
Low current mode: 15/25a
Weight: 3.5 kg
Dimensions: 180 x 249 x 100 mm
The Victron Phoenix Smart IP43 12/30 (1+1) 120-240V charger has an integrated wireless solution for configuring, monitoring, controlling, updating and synchronizing the Phoenix Smart IP43 chargers.
The second output, limited to approximately 4 A and with a slightly lower output voltage, is intended to fully charge a starter battery.
Each of the outputs can supply the full rated output current. But the three outputs combined can never exceed the rated current of the charger.
The Victron Phoenix Smart IP43 12/30 (3) 120-240V charger compensates for the voltage drop of DC cables by gradually increasing the output voltage when DC current increases. Please refer to the manual for more information.
The Phoenix Smart Charger features our well-known "adaptive" battery management system that can be configured for different battery types. Its "adaptive" function will automatically optimize the charging process based on the battery usage.
When the discharge is low (e.g. a yacht connected to the pontoon) the absorption charging phase is shortened to avoid overcharging the battery. After a deep discharge, the absorption charge time is automatically increased to ensure a complete recharge of the battery.
If, in order to charge a battery quickly, a combination of high charge current with high absorption voltage has been chosen, the charger will prevent damage from over-gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached.
The storage mode is activated when the battery has not been discharged for 24 hours. In storage mode, the float voltage is reduced to 2.2 V/cell (13.2 V for 12 V batteries) to minimize gassing and corrosion of the positive plates. Once a week, the voltage is brought back up to the absorption level to "equalize" the
battery. This function prevents electrolyte stratification and sulfation, the main causes of battery failure.
Simple on/off control can be implemented by connecting a relay or optocoupler with open collector output from a Li-Ion BMS to the remote on/off port. Alternatively, full voltage and current control is also possible via Bluetooth.
The charging algorithm can be programmed via Bluetooth or the VE.Direct interface. Three preprogrammed charging algorithms can be selected with the mode button (see specifications).
A Smart Battery Sense sensor or BMV-712 Smart battery monitor can be used to communicate battery voltage and temperature to one or more Phoenix Smart IP43 chargers.
For a wired data connection to a GX device, such as the Cerbo GXto a PC or other devices. It also enables the Instant Readout function, through VictronConnect remotely from the VRM.
It can be programmed with the VE.Direct interface or with a Bluetooth-enabled device to trigger an alarm or other events.
When pairing two or more Phoenix Smart IP43 chargers in a VE.
View Victron Phoenix Smart Charger IP43 12/50 (3) - PSC125053085 data sheet
Weight | 3,7 kg |
---|---|
Dimensions | 10 × 24,9 × 18 cm |
You must be logged in to post a review.
At FVComponentes.com we have stock of the references with the highest rotation, however our catalog is so wide and economical because with many of the references we work under order. This means that the delivery time can be extended for 1-2 weeks + subsequent shipment by us. Thanks to this we can offer super competitive and attractive prices to the customer difficult to match. If you wish, you can write us to the chat on the page, call us at 968 97 83 01 or write to us at comercial@fvcomponentes.com to check if we have stock or the delivery time of the component you wish to purchase before finalizing the order.
Reviews
There are no reviews yet.